Skip to main content

Site Photo Capture Guide

8 required photos (4 sides + 4 corners, Hover-style) plus a few detail close-ups (electrical panel, HVAC, ambiguities). 5 to 8 minutes per property. Gives Assisted Design the ground-level

HowHow to capture site photos on a phone or iPad so Artemis can deliver an accurate design. About 5 to 8 minutes per property.

Satellite imagery covers most of what a designer needs to plan a project, but it misses the details that only show up at ground level: overhangs, dormers, material transitions, the back face of a two-story roof, the location of the main electrical panel. Site photos fill that gap.

You'll take 8 photos around the property, plus a few close-ups of features that matter for solar (the electrical panel, the HVAC unit, anything unusual on the roof). That's it.

If you've done this before, the Quick Reference below is all you need.


Quick Reference

Phone setup, once per device:

  • Live Photos OFF

  • Smart HDR OFF

  • Aspect ratio 4:3

  • Camera lens set to 1x (not 0.5x, not 2x)

  • Long-press the front door on screen to lock exposure (a yellow "AE/AF LOCK" banner appears at the top)

The capture, every time:

  • 5 to 8 minutes total

  • 8 photos required: one at each of 8 positions around the property (4 sides and 4 corners)

  • Plus a few detail close-ups if the property has solar-relevant features (electrical panel, HVAC, existing panels, anything unusual)

  • Typical total: 8 to 15 photos

The 8 required photos:

  • 4 sides (front, right, back, left): one photo each, taken 20 to 25 ft back, with the full wall in frame

  • 4 corners (front-right, back-right, back-left, front-left): one photo each, taken at a 45° angle so both adjacent walls are visible


Before You Go (One-Time Phone Setup)

Do this once on the device you'll use for captures. It takes 90 seconds.

Step 1: Adjust the camera defaults

Open Settings → Camera:

  • Formats: leave on "High Efficiency" (HEIC) unless your organization requires otherwise

  • Preserve Settings: turn ON "Exposure Adjustment" and "Live Photo" (this keeps Live Photo disabled across sessions)

  • Composition: turn OFF "View Outside the Frame"

  • HDR (Smart HDR): turn OFF

Why these matter: Live Photos add motion blur to every shot. Smart HDR adjusts colors between frames in a way that hurts reconstruction. "View Outside the Frame" quietly captures area beyond what you see on screen.

Step 2: Set up the Camera app

Open the Camera app:

  • Swipe up on the viewfinder (or tap the chevron at the top) to show the toolbar

  • Live Photos icon (yellow circle): make sure it is crossed out

  • Aspect ratio: tap and set to 4:3

  • Lens selector (just above the shutter): tap to 1x. Do not use 0.5x ultrawide. Do not use 2x or 3x telephoto.

Step 3: Confirm before you start

Check the bottom of the viewfinder. You should see:

  • "1×" highlighted (not 0.5× or 2×)

  • No yellow Live Photo badge

  • Aspect ratio reads 4:3

You're ready.


The Capture (5 to 8 Minutes)

You'll take 8 photos by standing at 8 specific positions around the property. One photo per position. No need to walk a continuous loop.

Step 1: Lock exposure

Stand in front of the property. Point the camera at the front door. Press and hold the front door on the screen for about 2 seconds, until a yellow "AE/AF LOCK" banner appears at the top.

You've just told the phone "this is the right brightness and focus for the whole capture." Do not tap the screen again until you're done. If the light changes dramatically (a cloud passes, you move from sun into shade), restart the capture and lock again.

Step 2: The 8 photos

Take them in this order. One photo at each position.

#

Position

How to stand

What's in frame

1

Front side

20 to 25 ft back from the center of the front wall

Full front wall, with a little margin on each side and the roof line visible above

2

Front-right corner

At a 45° angle to the corner, far enough back

Both the front wall and the right wall, with the corner roughly in the middle

3

Right side

20 to 25 ft back from the center of the right wall

Full right wall

4

Back-right corner

45° to the corner

Back wall and right wall, corner in the middle

5

Back side

20 to 25 ft back from the center of the back wall

Full back wall

6

Back-left corner

45° to the corner

Back wall and left wall, corner in the middle

7

Left side

20 to 25 ft back from the center of the left wall

Full left wall

8

Front-left corner

45° to the corner

Left wall and front wall, corner in the middle

Keep the camera level on every shot. The roof line should appear naturally at the top of the frame, you don't need to tilt up.

Step 3: Detail close-ups (only if these features are present)

Walk in close (5 to 10 ft) and take one photo of each, if the property has it:

  • Main electrical panel (MPU): where the meter and breakers are. Required for any solar project.

  • HVAC unit: outdoor condenser, heat pump, or AC unit

  • Existing solar panels: if any are already installed

  • Anything ambiguous: dormers, skylights, chimneys, satellite dishes, roof material transitions, unusual flashing

Skip whatever isn't present. Quality matters more than quantity here.

Typical total: 8 to 15 photos.


What Good Looks Like

Review your photos before you leave the property. A good capture has all of these:

The whole wall is in frame. No half-wall, no cropped roof line, no neighbor's house filling the middle.

The camera is level. Walls look straight up and down, not leaning.

The exposure is consistent. All 8 photos look like they were taken in the same light. If one is suddenly bright or dark, AE/AF lock probably broke and you should redo that one.

Sharp, no motion blur. If you can read curb numbers or address signage in any photo that includes them, your photos are sharp.

No fingers, no lens flares, no reflections of you in windows. Move out of any reflective surface before you shoot.


What to Avoid

These mistakes cause a project to come back for a redo:

  • 0.5x ultrawide lens. The fisheye distortion makes reconstruction impossible. Always 1x.

  • Live Photos on. Adds motion blur to every shot.

  • Hard sun on the roof. On bright sunny days, capture the shaded side first, then the sunny side. Overcast or open shade is ideal.

  • Capturing at night. Auto-rejected. Reshoot during daylight.

  • Missing a position. All 8 are required. If a fence or obstacle blocks one, get as close to the angle as you can and add a note.

  • Tape measure or reference object in frame. Not needed. Scale is pinned by the address and satellite imagery.

  • Phone case covering the lens. Bulky cases (especially battery cases) can clip the field of view at 1x. Remove the case if you see vignetting at the corners.


After You Submit

After you attach the photos to the project, the system runs a quick automated check. About 15 minutes later, one of two things happens:

If the photos pass: the project moves forward in the design queue. You're done.

If the photos fail a check: the project will surface a retake reason. The named reasons are:

Reason

What it means

What to do

Blurry

One or more required photos is out of focus

Retake the affected shot from the same angle

Missing corner

A required side or corner photo is missing

Capture the missing one

Nighttime

Photos were taken in low light

Reshoot during daylight

Obstructed

A major obstruction (vehicle, dumpster, scaffolding) blocks the wall

Reshoot from a different angle, or attach a note that the obstruction is permanent

Too few images

Below the 8-photo floor

Complete the missing required photos

Low resolution

Photos look downsampled or screenshot-style

Reshoot using the device's native camera (not a screenshot or a forwarded thumbnail)

If a project hits a retake more than twice on the same property, the in-app help button (?) will open a support flow that routes the case to your account team.


Quick Troubleshooting

The viewfinder opens at "0.5x".
Tap the 1x label above the shutter button. The camera defaults to whichever lens was used most recently.


​The full wall doesn't fit in frame even at 25 feet.
This is a larger property, often a duplex or commercial structure. Take the photo from as far back as you can, keep the camera level. If you still can't fit the wall, capture it in 2 sections at slight angles and attach a note flagging the property size.


​The light changed dramatically mid-capture.
Long-press the screen to re-lock AE/AF, then redo any photos taken under the old light. Mixed exposure across the 8 photos is a retake.


​The back of the property is fenced and I can't access it.
Two options: ask the owner or occupant for side-gate access, or capture as much as you can from accessible angles and attach a note. The design team can sometimes work around partial access, but they'll request a follow-up if not.


​The phone keeps refocusing as I move.
AE/AF lock has dropped. Long-press the screen again to re-engage it. If it keeps dropping, close and reopen the Camera app.
​

The 1x lens looks too narrow for this property.
Walk back farther. Adding distance is always safer than switching to 0.5x. If the property is on a narrow lot and you've gone as far back as the lot allows, capture each wall in 2 sections at slight angles and attach a note.


Frequently Asked Questions

Can I use Android?
This guide is written for iPhone and iPad. The same physical principles apply on Android (1x main lens, locked exposure, level camera, full wall in frame), but the menu names differ. Refer to your device manufacturer's documentation for the equivalent settings, or check this guide's Android companion if your organization has provided one.

Can I shoot video instead of photos?
Photos are preferred. A still capture at each position gives the design system a known frame to work with. Video introduces motion blur, frame compression, and inconsistent exposure.

Can I use a drone?
Aerial imagery is a separate workflow handled by the platform's drone mapping product. If your organization has access to drone mapping, use that for the roof and the phone capture for ground-level details. Do not substitute drone photos for the 8-photo ground capture.

Can I use my phone's Pro RAW or burst mode?
Standard HEIC photos are preferred. Pro RAW is allowed but increases file size 10x with no quality benefit for this use case. Burst mode is allowed but only the first frame of each burst counts; the rest are ignored.

Do I need to capture the inside of the property?
No. Interior photos are not used in the design process at this time.

Will the photo requirements change in the future?
Possibly. The current 8-photo capture is what the design team needs today. As the platform's automated design capabilities expand, more photos may be requested to improve accuracy. If that happens, this guide will be updated and any new requirements will be reflected directly in the app.

What if the property is brand new and the satellite imagery is out of date?
Capture as you normally would. The design team will use your photos as the primary source. Attach a note if the property has been recently built or modified.

Did this answer your question?